Antifoam and Defoamer
Compound Application Table

 

Tramfloc Is Pleased To Announce We Have Updated Our Site For Easier Access And A Fresh Face.
Come Take A Look

TRAMFLOC, INC.
P.O. Box 350   Tempe, AZ   85280-0350
Telephone: 480-491-6895     Fax: 480-456-1664
Toll Free: 800-613-6803
water@tramfloc.com




click here for List of Antifoams/Defoamers  List of Antifoams and Defoamers


We have prepared a representative selection of technical data below.
For further information, please consult Tramfloc®, Inc.


[Section divider]

WASTEWATER TREATMENT

APPLICATION Defoamer Antifoam
MUNICIPAL Aeration 1140
1141
1143
1146
Clarifier 1103
1104
1107
Digester 1100
1141
1143
1146
Nocardia Foam 1103
1104
1143
1146
1147

INDUSTRIAL Effluent Processing 1110
1143
1146
Aeration 1146
1143
Clarifier 1147
1142
1144
1145
Digester 1146
1100
1141
1147

COOLING TOWERS Evaporator 1143
1146
1110
1108
1107
1111

POOLS & SPAS 1146 FG
1118 FG

FOOD PROCESSING General Washing/Fluming 1146
1147
1150
1151
1179
1153
1160
Potato Washing 1148
1149
1161
1162
1163
1164
Kosher Approved 1160
1161
1162
1167
1148
1149
Certified Organic 1149
1179
1153

MINERAL PROCESSING Acid Production 1169
1170
1171

If your particular application is not mentioned above, give us a call at 800-613-8603 where one of our application agents will be able to further assist you.

[Section divider]

[click here]TRAMFLOC® 1101 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1102 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1103 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1104 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1105 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1106 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1107 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1108 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1109 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1110 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1111 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1112 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1113 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1114 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1115 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1116 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1117 ANTIFOAM and DEFOAMER

[click here]TRAMFLOC® 1118ANTIFOAM and DEFOAMER

[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1101 ANTIFOAM and DEFOAMER

DESCRIPTION
TRAMFLOC® 1101 ANTIFOAM and DEFOAMER is a ten percent {10%} active, silicone emulsion with excellent stability and can be added directly to the foaming system.

TYPICAL PROPERTIES

Actives: 10% Silica-Filled Polydimethylsiloxane
Appearance: Creamy White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH: 5.5

TRAMFLOC® 1101 ANTIFOAM and DEFOAMER is dispersible from room temperature to just below the boil. It is effective at very low concentrations. Ten to fifty {10-50} ppm is a good starting point. The concentration can be adjusted to give the most economical concentration.

TRAMFLOC® 1101 ANTIFOAM and DEFOAMER is stable in acid, alkaline or neutral systems. Some of the recommended uses are in textiles, paper coatings, size mixes, printing ink manufacturing, wastewater ponds, and sewage systems.

TRAMFLOC® 1101 ANTIFOAM and DEFOAMER is a very stable product, yet it releases its silicone very rapidly when added to the foaming media. As with most defoamers, best results are obtained by adding it to the system before foaming starts.

FDA STATUS

TRAMFLOC® 1101 ANTIFOAM and DEFOAMER is manufactured in compliance with the regulations of the Food and Drug Administration as cited in 21 CFR, Section 176.200 (defoaming agents used in coatings) and Section 176.210 (defoaming agents used in the manufacture of paper and paperboard).

EPA STATUS

The ingredients in TRAMFLOC® 1101 ANTIFOAM and DEFOAMER are in compliance with 40 CFR 180.1001(d), exempted from the requirements of a tolerance for application on growing crops.

STORAGE

TRAMFLOC® 1101 ANTIFOAM and DEFOAMER should remain shelf stable for up to six {6} months in its original container. To avoid freezing, store above 40°F. Product may separate upon freezing.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.


Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1102 ANTIFOAM and DEFOAMER

DESCRIPTION

Tramfloc® 1102 ANTIFOAM and DEFOAMER is a water-dilutable, 10% active, silicone ANTIFOAM and DEFOAMER. It has been designed to control foam in water-based food and chemical processes. Tramfloc® 1102 is a long-lasting antifoam that is nearly inert.

TYPICAL PROPERTIES

Actives: 10% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH.: 4.0 To 5.0

FDA STATUS

Tramfloc® 1102 is manufactured in compliance with the regulations of the Food and Drug Administration as cited in 21 CFR 173.340, defoaming agents used in processing foods. Use quantities should be based upon the limitations as prescribed by the FDA.

USDA STATUS

Tramfloc® 1102 is chemically acceptable by the USDA for certain meat and poultry applications. For specific applications and/or limitations, please contact Tramfloc®, Inc.

EPA STATUS

40 CFR 180.1001©, exempted from the requirement of a tolerance for application on growing crops. Tramfloc® 1102 ANTIFOAM and DEFOAMER

USES

Tramfloc® 1102 is compatible in most wet processing applications, but it is advisable to pre-check each application. It is most effective when used to prevent foam formation; therefore, it is best to add Tramfloc® 1102 to the system before foaming starts. Tramfloc® 1102 concentration should be adjusted for each foaming system to determine the optimum concentration to use. It is suggested that the concentration can be decreased to establish the most economical quantity. Dilutions should be made by first charging water and then adding Tramfloc® 1102 . Mechanical mixing is required to ensure even distribution.

STORAGE

Tramfloc® 1102 should remain shelf-stable for up to 12 months in its original, sealed container. To avoid freezing, store above 40°F. Product may separate upon freezing.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.


Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1103 ANTIFOAM and DEFOAMER

DESCRIPTION

Tramfloc® 1103 Antifoam is a compound based on dimethyl polysiloxane fluid, developed specifically for the defoaming of aqueous or anhydrous media. It is a product regularly used in numerous industries, such as the chemical, rubber, paper, painting, textile and agrichemical industries.

FEATURES

Tramfloc® 1103 Antifoam presents a number of advantages, among which are the following:
* Excellent efficacy: Tramfloc® 1103 Antifoam is effective in a diluted form of between 1 and 200 parts per million of foaming medium.
* Chemically inert: Tramfloc® 1103 Antifoam is chemically inert in relation to the material to be defoamed. It will not modify the typical properties of any foaming media.

APPLICATION

Tramfloc® 1103 Antifoam may be used in many varied applications, as follows:

TYPICAL PROPERTIES

Chemical Nature: Compound Based On Dimethyl Polysiloxane Fluid
Appearance: Viscous, Homogenous Liquid
Color: Clear Grey; Translucent
Active Ingredients (%): 100
Diluents: Aromatic, Aliphatic, And Chlorinated Hydrocarbons
Specific Gravity @ 25°C: 1.0
Emulsifiers: None

EPA STATUS

The ingredients in Tramfloc® 1103 are listed in EPA Regulations, 40 CFR 180.1001(d), exempted from the requirements of a tolerance for application on growing crops.

PACKAGING

Tramfloc® 1103 Antifoam is available in 460-pound drums and bulk.

STORAGE

Tramfloc® 1103 Antifoam may be kept in its original, unopened container for twelve (12) months at room temperature.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.

Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1104 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1104 is a silicone-organic antifoam compound that is readily dispersible in water. It is for use in controlling foam in industrial aqueous systems over wide pH and temperature ranges. Tramfloc® 1104 provides a very convenient form of silicone antifoam compound that can be formulated into aqueous-based antifoams. Antifoams formulated with Tramfloc® 1104 can rinse free from substrates by flushing with water at room temperatures. Tramfloc® 1104 is manufactured in accordance with the Regulations of the Food and Drug Administration as described in 21 CFR, Section 176.210. The ingredients of Tramfloc® 1104 are in compliance with the EPA under 40 CFR 180.1001(c), "exempted from the requirements of a tolerance for application on growing crops or to raw agricultural commodities after harvest."

TYPICAL PROPERTIES

Appearance: Milky, White Liquid
Viscosity @ 25°C: 6,000 cps
Actives: 100%
Flash Point {cc}: Above 250°F

USES OF TRAMFLOC® 1104 ANTIFOAM

Tramfloc® 1104 has been especially prepared for the formulators of aqueous-based antifoams. It is easily extended with cool water to active levels as low as 5% or as high as 40%. The general procedure is to mix Tramfloc® 1104 into thickened water at room temperature. Without thickener, water emulsions are not stable. Thickened emulsions of Tramfloc® 1104 can be stable for prolonged periods, depending on the type and concentration of the thickener. Synthetic thickeners, such as Carbopol 990 (B. F. Goodrich) or Acrysol ASE-60 (Rohm & Haas), can be used. Preservatives may be used in the finished emulsions to retard microorganism growth.

STORAGE

Tramfloc® 1104 has a shelf life of up to 12 months in the original, unopened container. It is possible that may separate slightly during prolonged storage, especially under warm conditions. If separation does occur, mechanical mixing will restore it to original condition and efficiency. It will become much thicker as the temperature is decreased. If stored at low temperature, warm to above 15°C (60°F) prior to use.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.


Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1105 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1105 is a silicone-organic antifoam compound that is readily dispersible in water. It is for use in controlling foam in paper-making, aqueous systems over wide pH and temperature ranges. Tramfloc® 1105 provides a very convenient form of silicone antifoam compound that can be formulated into aqueous-based antifoams. Antifoams formulated with Tramfloc® 1105 are high temperature and high pH durable, providing improved "holdout" compared to other antifoams. Tramfloc® 1105 is manufactured in accordance with the Regulations of the Food and Drug Administration as described in 21 CFR, Section 176.210.

TYPICAL PROPERTIES

Appearance: Milky, White Liquid
Viscosity @ 25°C: 2,300 cps
Actives: 100%
Flash Point {cc}: Above 250°F

USES OF TRAMFLOC® 1105

Tramfloc® 1105 has been especially prepared for the formulators of aqueous-based antifoams. It is easily extended with cool water to active levels as low as 2% or as high as 40%. The general procedure is to mix Tramfloc® 1105 into thickened at room temperature. Without thickener, water emulsions are not stable. Thickened emulsions of Tramfloc® 1105 can be stable for prolonged periods, depending on the type and concentration of the thickener. Synthetic thickeners such as Kelzan S {Kelco Division of Merck} or Acrysol ASE-60 {Rohm & Haas} can be used. Preservatives may be used in the finished emulsions to retard microorganism growth.

STORAGE

Tramfloc® 1105 has a shelf life of up to 12 months in the original, unopened container. It is possible that Tramfloc® 1105 may separate slightly during prolonged storage, especially under warm conditions. If separation does occur, agitation will restore it to original condition and efficiency. It will become much thicker as the temperature is decreased. If stored at low temperature, warm to above 15°C (60°F) prior to use.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.


Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1106 ANTIFOAM and DEFOAMER
DESCRIPTION:

Tramfloc® 1106 Antifoam is a compound based on dimethyl polysiloxane fluid, developed specifically for defoaming over wide pH and temperature ranges. Tramfloc® 1106 Antifoam is ultimately formulated for industrial use only. Tramfloc® 1106 is manufactured in accordance with the Regulations of the United States Food and Drug Administration as described in 21 CFR Section 176.210, "defoaming agents used in the manufacture of paper and paperboard."

FEATURES

Tramfloc® 1106 Antifoam presents a number of advantages, among which are the following:
* Ease of use:
Tramfloc® 1106 Antifoam may be applied neat or diluted in a solvent or in a portion of the foaming medium.
* Excellent efficiency.
* Chemically inert.
Tramfloc® 1106 Antifoam is chemically inert in relation to the material to be defoamed. It will not modify the typical properties of any foaming media.

TYPICAL PROPERTIES

Chemical Nature: Compound Based On Dimethyl Polysiloxane Fluid
Appearance: Viscous, Homogenous Liquid
PACKAGING

Tramfloc® 1106 Antifoam is available in 460-pound drums and bulk.

STORAGE

Tramfloc® 1106 Antifoam may be kept in its original, unopened container for twelve (12) months at room temperature.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.


Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1107 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1107 is an excellent ANTIFOAM and DEFOAMER emulsion based upon a unique organic-polysiloxane compound. It is used for controlling foam in aqueous systems. Tramfloc® 1107 is compatible in most systems where foaming is a problem. It may be used in hot foaming systems {up to 180oF} and remain stable. After its use in high temperature environments, Tramfloc® 1107 can be rinsed away without oil scum deposits. Tramfloc® 1107 is stable in acid, alkaline, or neutral systems.

TYPICAL PROPERTIES

Appearance: Milky, White Liquid
Specific Gravity @ 20°C: 1.0
Viscosity {20°C} 1,000 -3,500 cps
Defoamer Actives: 20%
pH: 6-8

USES

Use levels of Tramfloc® 1107 depend upon the nature and severity of the foaming. Normally in latex systems, it should be evaluated initially as a pound-for-pound replacement for conventional defoamers. Dilutions of Tramfloc® 1107 should be made by first charging the water and then adding Tramfloc® 1107. Mechanical mixing is required to ensure even distribution. Water dilutions below 5% may have limited shelf stability.

FDA STATUS

Tramfloc® 1107 is manufactured in compliance with the Regulations of the Food and Drug Administration as cited in 21 CFR, Section 176.210 (defoaming agents used in the manufacture of paper and paperboard.)

FPA STATUS

The ingredients of Tramfloc® 1107 are listed in EPA Regulations, 40 CFR 180.1001(d), exempted from the requirements of a tolerance for application on growing crops.

STORAGE

Tramfloc® 1107 should remain shelf stable for up to 12 months in its original, sealed container. To avoid freezing, store above 40oF. Product may separate upon freezing.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.


Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1108 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1108 is a water-dilutable, 20% active, silicone ANTIFOAM and DEFOAMER. It has been designed to control foam in water-based food and chemical processes. Tramfloc® 1108 is a long-lasting antifoam that is nearly inert.

TYPICAL PROPERTIES

Atives: 20% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH: 4.5 to 6.0

FDA STATUS

Tramfloc® 1108 is manufactured in compliance with the regulations of the Food and Drug Administration as cited in 21 CFR 173.340, defoaming agents used in processing foods. Use quantities should be based upon the limitations as prescribed by the FDA.

USDA STATUS

Tramfloc® 1108 is chemically acceptable by the USDA for certain meat and poultry applications. For specific applications and/or limitations, please contact Tramfloc®, Inc.

EPA STATUS

The ingredients in Tramfloc® 1108 are listed in EPA Regulations, 40 CFR 180.1001(d), exempted from the requirements of a tolerance for application on growing crops for pesticide applications.

USES

Tramfloc® 1108 is compatible in most wet processing applications, but it is advisable to pre-check each application. It is most effective when used to prevent foam formation; therefore, it is best to add Tramfloc® 1108 to the system before foaming starts. Tramfloc® 1108 concentration should be adjusted for each foaming system to determine the optimum concentration to use. It is suggested that the concentration can be decreased to establish the most economical quantity. Dilutions should be made by first charging water and then adding Tramfloc® 1108. Mechanical mixing is required to ensure even distribution.

STORAGE

Tramfloc® 1108 has a shelf life of up to six 12 months in its original, unopened container.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.


Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1109 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1109 is a water-dilutable, 30% active, silicone ANTIFOAM and DEFOAMER. It has been designed to control foam in water-based food and chemical processes. Tramfloc® 1109 is a long-lasting antifoam that is nearly inert.

TYPICAL PROPERTIES

Actives:30% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH: 5.5

FDA STATUS

Tramfloc® 1109 is manufactured in compliance with the regulations of the Food and Drug Administration as cited in 21 CFR 173.340, defoaming agents used in processing foods. Use quantities should be based upon the limitations as prescribed by the FDA.

USDA STATUS

Tramfloc® 1109 is chemically acceptable by the USDA for certain meat and poultry processing applications. For specific applications and/or limitations, please contact Tramfloc®, Inc.

EPA STATUS

The ingredients in Tramfloc® 1109 are listed in EPA Regulations, 40 CFR 180.1001(d), exempted from the requirements of a tolerance for application on growing crops.

USES

Tramfloc® 1109 is compatible in most wet processing applications, but it is advisable to pre-check each application. It is most effective when used to prevent foam formation; therefore, it is best to add Tramfloc® 1109 to the system before foaming starts. Tramfloc® 1109 concentration should be adjusted for each foaming system to determine the optimum concentration to use. It is suggested that the concentration can be decreased to establish the most economical quantity. Dilutions should be made by first charging water and then adding Tramfloc® 1109. Mechanical mixing is required to ensure even distribution.

STORAGE

Tramfloc® 1109 should remain shelf stable for up to 12 months in its original, sealed container. To avoid freezing, store above 40oF. Product may separate upon freezing.


Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin
DESCRIPTION

Tramfloc® 1110 ANTIFOAM and DEFOAMER is a ten percent {10%} active, silicone emulsion with excellent stability and can be added directly to the foaming system.

TYPICAL PROPERTIES

Actives: 10% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Specific Gravity @ 25°C: 1.002
Emulsifier: Nonionic
pH: 5.5

Tramfloc® 1110 ANTIFOAM and DEFOAMER is dispersible from room temperature to just below the boil. It is effective at very low concentrations. Ten to fifty {10-50} ppm is a good starting point. The concentration can be adjusted to give the most economical concentration. Tramfloc® 1110 ANTIFOAM and DEFOAMER is stable in acid, alkaline or neutral systems. Some of the recommended uses are in textiles, paper coatings, size mixes, printing ink manufacturing, wastewater ponds, and sewage systems. Tramfloc® 1110 ANTIFOAM and DEFOAMER is a very stable product, yet it releases its silicone very rapidly when added to the foaming media. As with most defoamers, best results are obtained by adding it to the system before foaming starts.

FDA STATUS

Tramfloc® 1110 is manufactured in compliance with the regulations of the Food and Drug Administration as cited in 21 CFR, Section 176.200 (defoaming agents used in coatings) and Section 176.210 (defoaming agents used in the manufacture of paper and paperboard).

EPA STATUS

The ingredients in Tramfloc® 1110 are in compliance with 40 CFR 180.1001(d), exempted from the requirements of a tolerance for application on growing crops.

STORAGE

Tramfloc® 1110 should remain shelf stable for up to 12 months in its original container. To avoid freezing, store above 40oF. Product may separate upon freezing.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.

Tramfloc® 1110 ANTIFOAM and DEFOAMER




Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1111 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1111 is an excellent ANTIFOAM and DEFOAMER emulsion based upon a unique organic/polysiloxane compound. It is used for controlling foam in aqueous systems. Tramfloc® 1111 is compatible in most systems where foaming is a problem. It may be used in hot foaming systems {up to 180oF} and remain stable. Tramfloc® 1111 is stable in acid, alkaline, or neutral systems. It is compatible with foaming systems common to agrichemicals, coatings, chemical processing, carpet dyeing, industrial cleaners, and water treatments.

TYPICAL PROPERTIES
Appearance: Milky, White Liquid
Specific Gravity @ 20°C: 1.00
Viscosity {20oC}: 1,000-3,500 cps
Defoamer Actives: 15
pH: 6-8

USES

Use levels of Tramfloc® 1111 depend upon the nature and severity of the foaming. Normally in latex systems, it should be evaluated initially as a pound for pound replacement for conventional defoamers. Dilutions of Tramfloc® 1111 should be made by first charging the water and then adding Tramfloc® 1111. Mechanical mixing is required to insure even distribution. Water dilutions below 5% may have limited shelf stability.

EPA STATUS

The ingredients of Tramfloc® 1111 are listed in EPA Regulations, 40 CFR 180.1001(d) {exempted from the requirements of a tolerance for application on growing crops}.

STORAGE

Tramfloc® 1111 should remain shelf stable for up to 12 months in its original, sealed container. To avoid freezing, store above 40oF. Product may separate upon freezing.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.



Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1112 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1112 ANTIFOAM and DEFOAMER is a high active, silicone defoamer emulsion dispersible in warm or cold water. It is a stable emulsion in acid, alkaline, or neutral systems. It can be added directly to the foam system.

TYPICAL PROPERTIES

Defoamer Actives: 30%
Color: Off White
Physical Appearance: Pourable, Creamy Liquid
Stability: Greater Than Six Months
Emulsifier: Nonionic

Tramfloc® 1112 ANTIFOAM and DEFOAMER is compatible in most wet processing applications, but it is advisable to pre-check each application. The small amount required should not introduce any compatibility problems, even in conditions of strong electrolytes, etc. Tramfloc® 1112 ANTIFOAM and DEFOAMER is most effective when used to prevent foam formulation; therefore, it is best to add it to the system before foaming starts. Tramfloc® 1112 ANTIFOAM and DEFOAMER concentration should be adjusted for each foaming system to determine the optimum concentration to use. It is suggested that the concentrations can be decreased to establish the most economical concentration. Dilutions should be made by charging the water with Tramfloc® 1112. Mechanical mixing is required to ensure even distribution. Water dilutions below 10% may have limited shelf stability. Consult Tramfloc®, Inc. for dilution procedures.

FDA STATUS
Tramfloc® 1112 is manufactured in compliance with the Regulations of the Food and Drug Administration as cited in 21 CFR, Section 176.210 {paper and paperboard defoamers}.

EPA STATUS

Exceptions from the requirement of a tolerance {40 CFR 180.1001(d)} inert {or occasionally active} ingredients for use in formulations applied to growing crops.

STORAGE

Tramfloc® 1112 has a shelf life of up to twelve months in its original, unopened container.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.



Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1113 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1113 ANTIFOAM and DEFOAMER is a highly active, silicone defoamer emulsion dispersible in warm or cold water. It is a stable emulsion in acid, alkaline, or neutral systems. It can be added directly to the foam system.

TYPICAL PROPERTIES

Defoamer Actives: 33%
Color: Off White
Physical Appearance: Pourable, Creamy Liquid
Stability: Greater Than Six Months
Emulsifier: Non-Ionic

Tramfloc® 1113 ANTIFOAM and DEFOAMER is compatible in most wet processing applications, but it is advisable to pre-check each application. The small amount required should not introduce any compatibility problems, even in conditions of strong electrolytes, etc. Tramfloc® 1113 ANTIFOAM and DEFOAMER is most effective when used to prevent foam formulation; therefore, it is best to add it to the system before foaming starts. Tramfloc® 1113 ANTIFOAM and DEFOAMER concentration should be adjusted for each foaming system to determine the optimum concentration to use. It is suggested that the concentrations can be decreased to establish the most economical concentration. Dilutions should be made by first charging the water and then adding Tramfloc® 1113. Mechanical mixing is required to ensure even distribution. Water dilutions below 10% may have limited shelf stability. Ask us for dilution procedures.

FDA STATUS Tramfloc® 1113 is manufactured in compliance with the Regulations of the Food and Drug Administration as cited in 21 CFR, Section 176.210 {paper and paperboard defoamers}.

EPA STATUS Exception from the requirements of a tolerance {40 CFR 180.1001(d)} inert {or occasionally active} ingredients for use in formulations applied to growing crops.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.



Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1114 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1114 Antifoam is an excellent ANTIFOAM and DEFOAMER emulsion based upon a unique organic/polysiloxane compound. It is used for controlling foam in aqueous systems. Tramfloc® 1114 Antifoam has been designed for improved shelf life at lower concentrations. It is compatible in most systems where foaming is a problem. Tramfloc® 1114 Antifoam may be used in hot foaming systems {up to 180°F} and remain stable. After its use in high temperature environments, it can be rinsed freely away without oil scum deposits. Its unique dispersing properties allow it to be used with most conventional aqueous systems without "fish-eye" effects. Tramfloc® 1114 Antifoam is stable in mild acid or alkaline systems.

TYPICAL PROPERTIES

Appearance: Milky, White Liquid
Specific Gravity @ 20°C: 1.00
Viscosity {20°C}: 1,000-2,000 cps
pH 6-8

FDA STATUS

Tramfloc® 1114 Antifoam is manufactured in compliance with the Regulations of the Food and Drug Administration as cited in 21 CFR, Sections 176.170 and 176.180, for use as a defoamer for coatings and adhesives that contact food.

STORAGE

Tramfloc® 1114 Antifoam has a shelf life of up to 12 months in its original, unopened container.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.



Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1115 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1115 Antifoam is an excellent ANTIFOAM and DEFOAMER emulsion based upon a unique organic/polysiloxane compound. It is used for controlling foam in aqueous systems. Tramfloc® 1115 Antifoam has been designed for improved shelf life at lower concentrations. It is compatible in most systems where foaming is a problem. Tramfloc® 1115 Antifoam may be used in hot foaming systems {up to 180°F} and remain stable. After its use in high temperature environments, it can be rinsed freely away without oil scum deposits. Its unique dispersing properties allow it to be used with most conventional aqueous systems without "fish-eye" effects. Tramfloc® 1115 Antifoam is stable in mild acid or alkaline systems.

TYPICAL PROPERTIES

Appearance: Milky, White Liquid
Specific Gravity @ 20°C: 1.00
Viscosity {20°C}: 1,000-2,000 cps
pH 6-8

FDA STATUS

Tramfloc® 1115 Antifoam is manufactured in compliance with the Regulations of the Food and Drug Administration as cited in 21 CFR, Sections 176.170 and 176.180, for use as a defoamer for coatings and adhesives that contact food.

STORAGE

Tramfloc® 1115 Antifoam has a shelf life of up to 12 months in its original, unopened container.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.



Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1116 ANTIFOAM and DEFOAMER
DESCRIPTION

TRAMFLOC® 1116 is a fifty percent {50%} active, aqueous emulsion defoamer/antifoam based upon a unique organic-polysiloxane compound. It is for use in controlling foam in industrial aqueous systems over wide pH and temperature ranges. It may be used at room temperature or in hot foaming systems up to 200°F and will rinse freely from most substrates without depositing residual-free silicone fluid. TRAMFLOC® 1116 's unique dispersing properties allow it to be used in most aqueous foaming systems. It is compatible with foaming systems common to agrichemicals, aqueous polymer lattices, coatings, industrial cleaners and detergents, and textiles.

TYPICAL PROPERTIES

Appearance: Milky White Liquid
Solids: 50%
Viscosity @ 20°C: 2,000 To 7,000 cps
Solids: 50%
pH range: 5 to 7.0

USES

Use levels of TRAMFLOC® 1116 depend upon the nature and severity of the foaming. TRAMFLOC® 1116 can be further extended with water to concentrations as low as 5%. Low active water dilutions should be stabilized with suitable suspension aids or thickeners to provide sufficient shelf stability. Mechanical agitation would be required. Consult Tramfloc®, Inc. for our dilution procedures.

FDA STATUS

TRAMFLOC® 1116 is manufactured in compliance with the regulations of the Food and Drug Administration as cited in 21 CFR, Section 176.210 (defoaming agents used in the manufacture of paper and paperboard).

EPA STATUS

The ingredients in TRAMFLOC® 1116 are in compliance with 40CFR 180.1001(d), exempted from the requirements of a tolerance for application on growing crops.

STORAGE

TRAMFLOC® 1116 should remain shelf stable for up to 12 months in its original, sealed container. To avoid freezing, store above 40°F. Product may separate upon freezing.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.



Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1117 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1117 is a fifty percent {50%} active, aqueous emulsion defoamer/antifoam based upon a unique organic-polysiloxane compound. It is for use in controlling foam in industrial aqueous systems over wide pH and temperature ranges. Dilutions of Tramfloc® 1117 can be used in systems compatible with foaming common to agrichemicals, aqueous polymer latices, industrial cleaners, and textiles.

TYPICAL PROPERTIES

Appearance: Milky White Liquid
Viscosity @ 20°C: 2,000 To 5,000 cps
Solids: 50%
pH Range: 7.5 to 9.5

USES

Use levels of Tramfloc® 1117 depend upon the nature and severity of the foaming. Tramfloc® 1117 can be further extended with water to concentrations as low as 5%. Low active water dilutions should be stabilized with suitable suspension aids or thickeners to provide sufficient shelf stability. Mechanical agitation would be required. Consult Tramfloc®, Inc. for our dilution procedures.

FDA STATUS

Tramfloc® 1117 is manufactured in compliance with the regulations of the Food and Drug Administration as cited in 21 CFR, Section 176.210 (defoaming agents used in the manufacture of paper and paperboard).

EPA STATUS

The ingredients in Tramfloc® 1117 are in compliance with 40CFR 180.1001(d), exempted from the requirements of a tolerance for application on growing crops.

STORAGE

Tramfloc® 1117 should remain shelf stable for up to 12 months in its original, sealed container. To avoid freezing, store above 40°F. Product may separate upon freezing.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.



Return To Listing


[Section divider]



TRAMFLOC®, INC.
P.O. Box 350, Tempe, AZ, 85280-0350 Voice:480-491-6895 Fax:480-456-1664

Technical Information Bulletin


Tramfloc® 1118 ANTIFOAM and DEFOAMER
DESCRIPTION

Tramfloc® 1118 ANTIFOAM and DEFOAMER is a thirty percent active, silicone emulsion with excellent stability and can be added directly to the foaming system.

TYPICAL PROPERTIES

Actives: 30% Silica-Filled Polydimethylsiloxane
Appearance: Cream White Liquid
Emulsifier: Nonionic
pH: 4.0 To 5.0

Tramfloc® 1118 ANTIFOAM and DEFOAMER is dispersible from room temperature to boil. It is effective at very low concentrations. Ten to fifty ppm is a good starting point. The concentration can be adjusted to give the most economical concentration.

Tramfloc® 1118 ANTIFOAM and DEFOAMER is stable in acid, alkaline, or neutral systems. Some of the recommended uses are in textiles, paper coatings, size mixes, printing ink manufacturing, wastewater ponds, and sewage systems.

Tramfloc® 1118 ANTIFOAM and DEFOAMER is a very stable product, yet it releases its silicone very rapidly when added to the foaming media. As with most defoamers, best results are obtained by adding it to the system before foaming starts.

FDA STATUS

Tramfloc® 1118 ANTIFOAM and DEFOAMER is manufactured in compliance with the regulations of the Food and Drug Administration as cited in 21 CFR, Section 176.200 (defoaming agents used in coatings) and Section 176.210 (defoaming agents used in the manufacture of paper and paperboard).

EPA STATUS

The ingredients in Tramfloc® 1118 ANTIFOAM and DEFOAMER are listed in EPA Regulations, 40 CFR 180.1001(d), exempted from the requirements of a tolerance on growing crops.

STORAGE

Tramfloc® 1118 ANTIFOAM and DEFOAMER should remain shelf stable for up to 12 months in its original, sealed container. To avoid freezing, store above 40oF. Product may separate upon freezing.

The above data is based upon information Tramfloc®, Inc. believes reliable and is supplied for informational purposes only. Tramfloc®, Inc. disclaims any liability for damage or injury which results from the use of the above data and nothing contained herein shall constitute a guarantee, warranty (including warranty of merchantability or fitness for a particular purpose) or representation (including freedom from patent liability) by Tramfloc®, Inc. with respect to the accuracy or completeness of the data, the product described, or their use for any specific purpose even if that purpose is known to Tramfloc®, Inc. The final determination of the suitability of the information, the manner of use of the information or product and potential infringement of patents is the sole responsibility of the user.



Return To Listing


[Home Page]


Last Updated July, 2013

Copyright ©1997-2013 Tramfloc®, INC.   All Rights Reserved.